Just how do you really feel on the subject of How to Install a Bathtub?
Setting up a tub isn't exactly brain surgery, yet it does require strong plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a new one is additionally a moderately hard job. If the old bathtub is conveniently available, the job can relocate rapidly; if you have to open up a wall surface to eliminate the old tub and place the new bathtub, the task is much harder. In either case, the project is within a house handyman's skills, although you will require a helper to leave the old tub and embeded in the brand-new one. Make certain you have actually certified yourself for the task and also fit attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is far better to think about employing one prior to you begin. Possibilities are you might require a professional plumber to make tube links.
This article will certainly assist you install a new bathtub in your washroom if you have actually currently bought a new bathtub and do not need to change the arrangement of your previous water pipelines.
Your tools and product list ought to comprise the following:
Preparing for the Installation
To start with, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to avoid strain on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be suited its last position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. When the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Making use of both wooden boards under its feet, put the tub in the required placement. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four little points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit the bottom of the furthest versatile tap connector to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the supply of water as well as examine all joints as well as brand-new pipework for leakages and also tighten them if necessary. Load the tub and also check the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and sealing around the bath tub ought to wait up until the bathtub has been made use of at least once as this will resolve it right into its last position.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area between the tap and the sink. Safeguard the tap in place with the manufacturer given backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap adapters. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break an inflexible seal, creating the water to permeate the wall surface between the bathroom and also the tiling, leading to complications with moisture and possible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can fracture relatively very early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads on Tools You Need to Install a New Bathtub , I was thinking sharing that excerpt was worthwhile. Those who liked our blog posting plz remember to pass it around. I praise you for your time. Visit us again soon.
Get professional leak detection today.